Lyophilization Process Flow and Process Method

📅 September 11, 2026👤 By Anne⏱ 120 min read📂
Article Summary

The freeze-drying process mainly consists of three stages freezing → primary drying → secondary drying. Among them, primary drying is usually the longest stage in the entire freeze-drying cycle and also the stage where process optimization is most needed.

I. Freezing

1. Loading

The lyophilization process begins when the product is loaded into the freeze dryer.

For products with good stability at room temperature, loading can generally be performed at approximately 20–25°C. For products with relatively poor stability at room temperature, the loading temperature can be lowered according to the characteristics of the product, for example, to approximately 5°C.

After loading, the product should be allowed to reach an appropriate degree of thermal equilibration, taking into consideration factors such as the product fill volume, container specifications, equipment conditions, and the initial product temperature, before the freezing process begins.

2. Cooling and Freezing

The freezing process generally proceeds through the following stages:

Shelf cooling → Solution supercooling → Ice nucleation → Ice crystal growth → Complete freezing

However, the shelf temperature is not the same as the actual product temperature.

Therefore, lyophilization process design should not rely solely on the set temperature of the freeze dryer. Changes in the actual product temperature must also be taken into consideration.

Freezing is a very important stage of the lyophilization process because the ice crystal structure formed during freezing affects the resistance to water vapor transfer during primary drying, which in turn affects the structure of the dried cake, drying rate, and final product quality.

3. Annealing

The primary purpose of annealing is to promote ice crystal growth and crystallization of certain excipients, thereby reducing resistance to water vapor transfer during drying and potentially shortening the primary drying time.

However:

Annealing is not a mandatory step for every product.

Whether annealing should be used depends on factors such as the formulation characteristics, whether the product forms an amorphous or partially crystalline system, whether crystallization of certain excipients is desired, key thermal properties such as Tg′, product stability, and the final quality of the lyophilized product.

The annealing conditions should be determined based on the formulation and crystallization behavior. In some development studies, conditions such as −15°C to −10°C for 3–5 hours may be evaluated, but these are only reference conditions for process development and should not be regarded as fixed parameters applicable to all products.

Annealing may also have negative effects, including causing phase separation in certain systems, changing the crystal form of excipients, affecting secondary drying, or, in some cases, increasing the overall lyophilization cycle time. Therefore, during product development, annealing should be compared and validated rather than automatically applied to every product.

For systems containing crystalline excipients, it is also necessary to consider the timing and crystal form of excipient crystallization, as the crystallization behavior of excipients may affect product stability.

II. Primary Drying

The primary drying process mainly involves reducing the chamber pressure to allow the frozen ice to undergo sublimation, thereby removing most of the water from the product.

Primary drying is usually the longest stage of the entire lyophilization cycle and offers the greatest opportunity for optimizing and shortening the overall cycle time. However, primary drying is not simply a matter of making the process “as fast as possible.”

Increasing the product temperature can generally:

Increase the sublimation rate → Shorten the primary drying time

However, if the product temperature becomes too high, it may result in:

Collapse → Loss of dried-cake structure → Poor appearance → Changes in reconstitution, residual moisture, and other quality attributes

Therefore, the actual objective is:

To achieve the highest practical product temperature without exceeding the critical temperature of the product.

For amorphous systems, the collapse temperature is generally an important parameter to consider. For partially crystalline systems, the relevant critical temperatures associated with crystallization, melting, or other phase transitions should also be considered.

In general, an appropriate safety margin may be maintained below the critical temperature. The specific margin should be determined based on factors such as the duration of primary drying, product characteristics, and potential process variability.

Shelf temperature + chamber pressure determine the heat input to the product and the conditions for water vapor transfer, which in turn determine the product temperature. The product temperature should remain below the relevant critical temperature.

Our primary drying process is not designed solely based on experience. Instead, heat and mass transfer models are used to predict product temperature, sublimation rate, and primary drying time, supporting the design of lyophilization cycles for different formulations, vial sizes, fill volumes, and process conditions.

III. Secondary Drying

After primary drying is completed, the product does not contain absolutely no water.

At this stage, a certain amount of unfrozen and bound water may still remain. The purpose of secondary drying is to further reduce the residual moisture content.

Therefore:

Primary drying: Mainly removes frozen water (ice)

Secondary drying: Mainly removes unfrozen and bound water

The design of secondary drying mainly considers temperature, time, and product stability.

Increasing the secondary drying temperature can generally accelerate the reduction of residual moisture. However, higher temperatures and longer drying times are not necessarily better. For sensitive products, excessive secondary drying may negatively affect product stability.

Therefore, the final process needs to achieve a balance between sufficiently low residual moisture and maintaining acceptable product quality.

For typical amorphous systems, a relatively controlled heating rate may be used to reduce the risk of structural changes or collapse.

For crystalline or semi-crystalline systems, a higher heating rate may be possible, but the final conditions must still be evaluated and validated for the specific product.

However, this does not mean that lower residual moisture always results in better product stability.

For some products, excessive drying may actually have a negative impact on long-term stability. Therefore, the objective is to achieve an appropriate residual moisture level while maintaining the required product stability, rather than simply minimizing the residual moisture as much as possible.

Related Products

Semaglutide

Semaglutide

HPLC ≥ 99% · COA
Tirzepatide

Tirzepatide

HPLC ≥ 99% · COA
Retatrutide

Retatrutide

HPLC ≥ 99% · COA
Share:LinkedInXFacebookEmail
← Back to Blog